General Membrane Sagitta
PHP2,733.33
Tax included
This is an APP (Attactic Polypropylene) plastomeric type modified waterproofing membrane. It consists of a specially formulated bituminous compound of distilled asphalt that is modified with selected high grade visco-elastic polymers and inert filler. APP material has a very good heat stability, very high softening point and good workability, specially in sub-tropic and tropic climate (like the Philippines). It can also be used in the exposed roofing system.
Physical and chemical Properties : APP modified compound
• Excellent cold flexibility - 0°C
• Excellent UV resistance
• Excellent elongation
• Excellent resistance to aggressive chemicals
• Extremely good elastic memory
• Excellent resistance to chemical agents and pollutants in the atmosphere
TWO TYPES OF SAGITTA :
| Type(A) - (1) SAGITTA P Non-woven spunbond polyester carrier : • High mechanical characteristics • High elongation • High puncture resistance • Will not decay |
(2) SAGITTA P 4KG Mineral slate chip finish • UV barrier increasing product life • reduces spread of flame • allows a range of different colours for the cap-sheet |
SAGITTA P is based on filaments of polyester which are then welded together. It is for this reason that it is called Non-woven.
This product has a good mechanical strength, and has a good dimensional stability.
The data beneath proves it so :
| Tensile strength longitudinal / transversal Elongation Tear Resistance |
= 400 / 300 N / 50 mm = 35% = 130 N |
SURFACE PREPARATION
Areas where materials are to be installed using the “torch-on” method must be clean, dry, smooth and treated with primer to ensure good bonding between the membrane and the sub-strate. The roof should also have appropriate falls to ensure that water will run towards the drains, and not cause ponding on the roof.
| COVERAGE PER ROLL : 10 SQ. METER | ||
| Edp No. | Description | Dimension / Roll |
| 04092-00004 | SAGITTA P3 Sand | 1 m (W) x 10 m (L) x 3 mm THICKNESS |
| 04092-00007 | SAGITTA P4 kG (Green) | 1 m (W) x 10 m (L) x 4 kgs /m² |
04092-00004
This is an APP (Attactic Polypropylene) plastomeric type modified waterproofing membrane. It consists of a specially formulated bituminous compound of distilled asphalt that is modified with selected high grade visco-elastic polymers and inert filler. APP material has a very good heat stability, very high softening point and good workability, specially in sub-tropic and tropic climate (like the Philippines). It can also be used in the exposed roofing system.
7 other products in the same category:
Diasen Acriflex Rapido, Grey
Price
PHP22,500.00
One-component water based waterproofing with high-speed drying. Liquid and ready to use, formulated with elastomeric resins that can be applied outside, in case of low temperature and of high relative humidity level. Flexible, crack bridging and stagnant water resistant after a few hours from application. It is suitable for concrete-asbestos encapsulation, according to the current regulations in force.
Diasen Vapostop
Price
PHP8,060.00
One-component water based primer formulated with modified-silanepolymers and designed for concrete supports. Created to increase the adhesion degree waterproofing and acrylic coatings, the product creates a vapour barrier and avoids the development of blistering phenomenon and detachments caused by moisture. It can be applied even on moist supports, it is water resistant, it has excellent anti-degradation properties of concrete surfaces and it stops the carbonation phenomenon as well
Diasen WATStop, Black
Price
PHP13,800.00
Epoxy-cement waterproofing (Water Barrier)Three component epoxy resin to waterproof both with negative and positive pressure, to be used as osmotic over undergorund walls, to encapsulate rising damp and to realize a vapour over moist subtract. The product is formulated with a special epoxy resin (Part A), a catalyst (part B) and special cement (part C)